Water Butt Replacement Tap

Product Information

Undo it fully and remove it. Once you have, the old tap should now be loose and you can now remove it.

These are the fittings that feature a compression cap, an olive that slides over pipe and a compression joint body and are normally made from copper.In terms of how your tap gets it’s supply of water, regardless of the type of actual fitting (more on this below) is through what is known as a tap connector. With the tap end connected you can now connect the other end to the supply pipe. If you’re using the same connector or a new replacement of the same then push on the push fit or add a compression nut and olive and run it up finger tight before tightening with a wrench. In essence, a threaded spindle with a washer on one end and handle on the other lowers of raises (screws up or down) the washer in to and out of a seat in the base of the tap body to increase or decrease and stop the flow of water. As I’m sure you can imagine, pillar taps are available in a huge range of styles and designs. Older style taps, with the cross bar at the top are normally referred to as Capstan Head taps. Normally the body of the tap which connects the valve and spout rests on the upper surface of the basin, the tails protrude through holes in the basin to meet the supply pipes.

Fear not, in this project we will take you through the process of how to change a tap, beit a kitchen mixer tap or a bath tap, although they may look totally different, the principles of the job are the same. This can include bath taps, basin taps and kitchen taps as long as they are not single-lever taps. Tap Washer Replacement StepsTo avoid these issues, most add some PTFE tape around the threads of the compression joint body, but this doesn’t always solve the problem. Firstly before we begin, turn the water off. If you’re fortunate enough to have an isolation valve on the supply pipe you can turn the water off there. More information on the types of push fit fitting and how to use them can be found in our project here. What are the Different Types of Tap Mechanism?

Note: If the nut looks rusty or corroded, apply some easing fluid such as 3-in-1 oil or WD40 after giving it a good clean and removing as much debris as possible. Aside from the traditional looking mixer tap, todays more modern mixer taps can look more like a single pillar tap. Commonly known as Monobloc Taps, these modern sleek and attractively designed taps fit very well with todays popular and minimalist look. The majority of wash basins, baths and sinks are fitted with individual taps, one that supplies the hot and the other for the cold water. Individual supply taps of this nature are called pillar taps. In essence, the traditional style mixer tap is just two pillar taps joined together so that they share one spout. In terms of the actual connection between supply pipe and tap, this will either be a flexi pipe or the copper supply pipe will run all the way up to the tap.

How to Replace Old Taps With New

If you’re project involves working with the latter mentioned above then you are better off cutting off around 150 – 200mm off of the existing pipe and fitting a push fit flexi hose instead of trying to fit your tap to old and corroded existing fittings, much less of a headache! With everything now connected up it’s time to turn the water on and make sure everything is working and there aren’t any leaks. Both rigid and flexi hose connections also come with several different methods of actually making the connection from the supply pipe to the tap. This type of tap is pretty similar to the rising spindle type above in terms of the fact that the tap head screws a spindle with a seal at its base up and down, but instead of the seal turning with the spindle (as it does with the above mechanism), with this it is simply raised and lowered Changing a tap is a relatively simple DIY job if you have a sound knowledge of basic plumbing, but if you are new to this world, it may seem like a daunting task.

The mixer tap is most commonly found attached to kitchen sinks and also baths and in the case of bath mixers, they can sometimes also feature a shower hose (known as a shower tap). As the seal is effectively not screwed down into its seat, this does in some ways reduce the wear and tear placed on both the seal and the seat so on the whole, they are a little more reliable than their rising spindle counterparts.

Once chopped off, use some fine grade sandpaper or wire wool to clean the end of the pipe fully. Make sure there is no dirt, grime, corrosion, old paint or anything else left that will end up inserted inside your chosen fitting as this could affect the seal and cause leaks. If you are new to the world of plumbing then it’s a good idea to start off with these fittings. Not only are they easy to fit, they are also easy to remove again if you need to make any changes. Just push the joint down while pulling up the collar and then you can pull the fitting off. The monobloc tap is in some ways the best of both worlds; small and compact with all the benefits of a traditional mixer tap. These types of taps are simple in design as essentially, the sealing washer is screwed up or down to and from the seat, but do cause a lot of issues due to washers and seats wearing and corroding and causing leaks.